HELMET SIZING
HELMET SIZING
| SIZE | INCHES | CM | HAT SIZE |
|---|---|---|---|
| XS | 20 7/8 - 21 1/4 | 53 - 54 | 6 5/8 - 6 3/4 |
| SM | 21 5/8 - 22 | 55 - 56 | 6 7/8 - 7 |
| MD | 22 7/16 - 22 3/4 | 57 - 58 | 7 1/8 - 7 1/4 |
| LG | 23 1/8 - 23 5/8 | 59 - 60 | 7 3/8 - 7 1/2 |
| XL | 24 - 24 3/8 | 61 - 62 | 7 5/8 - 7 3/4 |
| 2XL | 24 3/4 - 25 3/16 | 63 - 64 | 7 7/8 - 8 |
| 3XL | 25 9/16 - 26 | 65 - 66 | 8 1/8 - 8 1/4 |
| 4XL | 26 3/8 - 26 3/4 | 67 - 68 | 8 3/8 - 8 1/2 |
HELMET LINER CHART
PROPER FIT:
Start by measuring the circumference around your head using a soft tape measure. Starting at your forehead just above the eyebrow line (approximately one inch above) and across the largest portion of the back of your head. Repeat the process to confirm the measurement. Select the helmet size from the chart below that is closest to your measurement.
Measuring Tape Placement
NOTE:
The sizing chart is simply a starting guide, as head shapes vary. For the best fit visit an authorized Scorpion Exo Dealer.
FITMENT:
It is important for maximum safety that your Scorpion Exo® helmet fits snugly and comfortably on your head with the retention strap (chinstrap) properly and snugly fastened.
Do not simply pull your helmet down onto your head like a hat. Your ScorpionExo® helmet should be worn as follows:
Using both hands, grasp both chinstraps and the helmet’s bottom trim at the same time and pull the helmet down over your head until you feel the top of the helmet snugly against your scalp.
Next, grasp the helmet (as shown) and try to “roll” the helmet forward on your head. If you can roll the helmet so the top of the eye port comes down past your brow, it is too loose, try on a smaller size.
Repeat this process until you find a size that is comfortable yet snug enough as to not slide on your head. The helmet should be snug enough to move the skin on your forehead.
HEAD SHAPE REFERENCE
HEAD SHAPE REFERENCE
OVAL HEAD SHAPE
OVAL HEAD SHAPE
- EXO-R2000
- EXO-GT3000
INTERMEDIATE OVAL HEAD SHAPE
INTERMEDIATE OVAL HEAD SHAPE
- EXO-R1 AIR CARBON
- EXO-R1 AIR
- EXO-ST1400 CARBON
- EXO-T520
- COVERT FX
- COVERT 2
- EXO-HX1
- EXO-R420
- EXO-R320
- EXO-GT930
- EXO-AT960
- EXO-AT950
- XT9000
- VX-16
ROUND HEAD SHAPE
ROUND HEAD SHAPE
- COVERT
- OPTIONAL CHEEK PAD FITMENT
| Shell | SCORPION EXO PART# | |||
|---|---|---|---|---|
| SHELL #1 | SCORPION EXO PART# | XS | SMALL | MEDIUM |
| R1-650-02 | Standard | + 5mm (Thicker) | + 10mm (Thicker) | |
| R1-650-03 | - 5mm (Thinner) | Standard | + 5mm (Thicker) | |
| R1-650-04 | - 10mm (Thinner) | - 5mm (Thinner) | Standard | |
| R1-650-14 | - 15mm (Thinner) | - 10mm (Thinner) | - 5mm (Thinner) | |
| SHELL #2 | SCORPION EXO PART# | LARGE | ||
| R1-650-05 | Standard | |||
| R1-650-15 | - 5mm (Thinner) | |||
| SHELL #3 | SCORPION EXO PART# | X-LARGE | 2X-LARGE | 3X-LARGE |
| R1-650-06 | Standard | + 5mm (Thicker) | + 10mm (Thicker) | |
| R1-650-07 | - 5mm (Thinner) | Standard | + 5mm (Thicker) | |
| R1-650-08 | - 10mm (Thinner) | - 5mm (Thinner) | Standard |
Optional cheek pads are available for all EXO-R1 Air helmets (CARBON and TCT-ULTRA)
